how to change belt on Shark Navigator

How to Change the Belt on a Shark Navigator Vacuum

Last Updated on

What is the purpose of replacing a vacuum cleaner’s belt? What should you do if your Shark Navigator has problems with suction power?

We understand that changing the belt on a Shark Navigator can be tricky, but keeping your vacuum running efficiently is necessary. Hence, this blog post included tips on how to change the belt on a Shark Navigator vacuum cleaner.

Signs You Need to Replace a Shark Vacuum’s Belt

Shark vacuum cleaners are designed with several features that make them efficient and easy to use. However, like all machines, they require occasional maintenance to continue running at their best.

The Shark Navigator has a belt that transfers power from the motor to the brush. Unfortunately, this means that belts will wear down over time and need replacement every so often.

How do you determine that the belt needs to be replaced? If you notice any of the following problems with your Shark vacuum cleaner, it may be time to replace the belt:

  • Your vacuum cleaner is leaving streaks or lines on the floor
  • The device is not picking up dirt as well or as effectively as it used to
  • The vacuum cleaner’s suction power has decreased
  • The vacuum’s cleaner’s roller brush isn’t spinning
  • Your Shark Navigator starts making a strange noise when you turn it on
  • The belt is visibly worn or damaged
  • The vacuum belt is stretched and no longer tight

If you noticed any of these problems, it’s time to replace your Shark Navigator’s belt! The good news is that this process is quick and easy. Follow the section below to replace a Shark vacuum belt successfully.

How to Change the Belt on a Shark Navigator Vacuum

Below is a step-by-step guide on Shark Navigator Lift-Away Pro belt replacement.

Step 1: Turn Off Your Shark Vacuum Cleaner

Turn off the appliance before changing the belt and unplug the power cord from the power supply. For newer models, remove any battery installed in the case of cordless units.

Step 2: Detach the Roller Brush

Remove the screws holding the cover in place with a flat head screwdriver. Lift the top lid.

If you have a Shark model with a brush roll, first release its locking mechanism by spinning the dial to remove the brush roll.

Step 3: Undo the Shark Vacuum Belt

Remove old belt by pulling it out from underneath roller brush and then replace with a new one! Make sure to use a bit of WD40, if needed, for ease of replacement.

Remove the old belt by carefully pulling it out of its grooves without damaging or stretching it. Make sure to keep your new belt away from staples and other sharp objects that could damage it during storage. If you have long hair, tie it back before proceeding so that you do not accidentally pull your hair into the belt.

Step 4: Clean the Vacuum Cleaner

After removing the worn-out belt, clean all parts of the vacuum thoroughly, including the brush roller, to avoid dust particles accumulating again in the drum or other places that can damage the new belt while spinning.

Step 5: Replace the Shark Navigator’s Belt

Install the replacement belt by stretching it across the barrel carefully such that teeth on the belt fit into grooves on the drum.

Release tension of the belt by spinning the dial and putting back the brush roller by reversing previous steps. Make sure that the new belt is properly in place and locked.

Step 6: Replace the Cover

Put the top cover back on and put back all the screws. Check that all parts are in place before turning on your vacuum cleaner.

If you cannot do this simple process yourself, then take help from experts. It is always better to be safe than sorry. So, follow these tips, and your vacuum cleaner will work like new again.

Tips for Maintaining Shark Vacuum Cleaners Tips

Here are some of the tips for maintaining your Shark vacuum cleaner:

Clean the Brush Roller

The brush roller should be cleaned often. If it is not clean, then dirt and dust will accumulate on the brush roll that can damage the belt. Sometimes you might find many human and pet hair wrapped around the roller. In that case, you need to remove all hair from the roller.

The brush roll should be cleaned often with a cloth or paper towel soaked in warm water mixed with liquid soap or detergent. If something is stuck on the drum, mix white vinegar with baking soda and rub it on the roller.

Check for Clogs

Empty the dust cup of dirt and debris. Also, check for clogs in the hose or filters. If there is any blockage, remove it and clean the vacuum thoroughly.

Inspect the Belt

The vacuum belt should be inspected regularly. If it is damaged or worn out, change the belt with a new one.

Store the Vacuum in an Upright Position

Keep the vacuum upright in a cool, dry place. Do not expose it to direct sunlight or heaters as it might damage the parts.

Follow these simple tips, and your vacuum cleaner will work like new again.

Safety Tips for Maintaining Vacuum Cleaners

Here are vacuum cleaner tips to keep in mind:

  • Always read the user manual carefully before using or cleaning your Shark vacuum cleaner to avoid any damages.
  • Make sure that all replacement parts fit your specific Shark vacuum cleaner model. There are many different models of Shark vacuums available. Hence, you should always have your model number at hand when purchasing replacement parts.
  • Do not try to fix any part of the vacuum yourself if you cannot do it perfectly. Otherwise, there is a risk of fire or injury.
  • Never leave the appliance unattended when it is plugged in. Vacuum cleaners are not meant for children to play with.
  • Be sure to unplug the vacuum cleaner from the wall before changing any of its parts.
  • If something goes wrong while trying to fix it, stop and get help.

These safety considerations are essential not just for maintaining your Shark vacuum cleaner but also for all other appliances in your home. By following these rules, you can avoid many accidents and injuries.

FAQs on Shark Vacuum Belt Replacement

Why Is the Brush on Shark Vacuum Not Spinning?

If your brush roll on Shark Navigator is not spinning, then either belt has broken, or there might be something stuck in the drum.

How Do I Clean My Shark Vacuum Cleaner?

Shark Navigator can be easily cleaned with a piece of cloth or paper towel soaked in warm water mixed with liquid soap or detergent.

Be careful while cleaning dirt cup assembly, edges of the dust bin, and exterior surfaces as they are very delicate and can get damaged if not cleaned properly.

Why Is My Shark Navigator Making a Loud Noise?

There are many reasons why your device is creating noises while cleaning like some object is stuck somewhere, hose connection is loose, or filters need to be cleaned or replaced.

How Often Should I Clean My Shark Navigator?

The vacuum cleaners are very efficient and effective. You do not require to clean it after every use, but you have to clean it from time to time to remain in tip-top shape for a longer time.

Is Shark Vacuum Belt Replacement Easy for Beginners?

Yes, you do not need to be an expert to change the belt. You can easily find replacement belts from any local store and install them carefully following the user manual.

Quick and Easy Shark Vacuum Belt Replacement

Most people think that it is not easy to maintain a vacuum cleaner, and they will not do it. However, now that you know how to change the belt on a Shark Navigator vacuum cleaner, keeping your machine will be so much easier.

If you have more questions about vacuum cleaner maintenance, let us know in the comments. We’d love to hear from you!

Additional Resources

About The Author

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top